2025 GMC Yukon Complaints

ENGINE — Filed 09/28/2026

Engine failure at 20,959 miles (GM 6.2L V8). Sudden knocking noise. I heard noise at idle, accelerating, and decelerating. Sounds increased in volume / frequency within a 24hr period and driving it only a few miles. GM dealer verified engine failure and is ordering a replacement under warranty.

ENGINE — Filed 11/02/2025

The contact owns a 2025 GMC Yukon. The contact stated that while driving 50 MPH, the vehicle started shuddering. The failure was a recurring failure. The dealer was contacted in person, and the failure was associated with the dynamic fuel management system. The manufacturer was contacted by phone and made aware of the failure. The failure mileage was approximately 375.

POWER TRAIN — Filed 09/17/2026

The contact owns a 2025 GMC Yukon. The contact stated that while driving approximately 10 MPH, the vehicle unexpectedly lost motive power and came to a complete stop in traffic. There was no warning light illuminated during the failure. The vehicle was restarted; however, the vehicle failed to shift into gear, and the “Service Transmission” message was displayed. The vehicle was towed to the dealer but was not diagnosed or repaired. The contact expressed concerns that the failure could have resulted in a crash or created a safety risk to the contact and the contact’s children while occupying the vehicle. The manufacturer was not made aware of the failure. The failure mileage was approximately 30,765.

ENGINE — Filed 08/11/2026

The contact owns a 2025 GMC Yukon. The contact stated that while driving at an undisclosed speed, the engine seized. No warning lights illuminated. The vehicle was towed to a dealer, where it was diagnosed that the engine, radiator, and an unknown belt needed to be replaced. The vehicle was repaired; however, the failure recurred. While driving at an undisclosed speed, several unknown warning lights illuminated, and the engine seized upon arriving at the dealer location. The vehicle failed to restart. The dealer diagnosed that the generator and air conditioner failed and needed to be replaced. The vehicle was in the process of being repaired. The manufacturer was notified of the failure, and a case was opened. The failure mileage was approximately 33,018.

ENGINE — Filed 08/14/2026

As my wife was driven she heard some noise and notice she was losing power. She pull off the side of the road and the car shut off. Could not restart. This happen about 11:30 am on 8/14/26 Got towed to Salida Dealer called Faricy GMC about 3:30 pm. Dealer said it was a complete engine failure and engine needed to be replaced.

ENGINE,FUEL/PROPULSION SYSTEM — Filed 08/21/2026

Vehicle loss of power on the Interstate at a high rate of speed. Vehicle would not start and could not be put in Neutral to safely remove from road.

STEERING,ELECTRICAL SYSTEM — Filed 08/04/2026

The progressive failure of the factory steering wheel adhesive on my 2025 GMC Yukon creates an immediate, active safety hazard during vehicle operation. The material failure and sticky glue are localized directly around the integrated heating element of the steering wheel. This failure severely impacts driving maneuvers as well as a potential electrical fire hazard. The liquefied glue residue is incredibly sticky and continually transfers to the driver’s hands, resulting in a compromised, slippery grip on the steering wheel. During active driving maneuvers, such as hand-over-hand turning, navigating sharp curves, the loose edges of the peeling leather and separating trim physically catch on the driver's palms. This restricts smooth wheel rotation, disrupts natural hand movement, and threatens a sudden, temporary loss of steering control. This manufacturing defect introduces severe driver distraction and physical interference with critical steering components while driving, compounded by a potential thermal or electrical defect in the steering wheel heating assembly.

POWER TRAIN,ELECTRICAL SYSTEM,ENGINE — Filed 06/26/2026

GM performed a vehicle wide Over the Air reprogramming of the modules incorporated in the VIP/Global B electronics platform in April, 2026. Following that my vehicle became totally dead. Key fob would not unlock the vehicle. Had to use the metal key, open the drivers door. Opened the door, nothing moved. No lights, no movement from anything on the vehicle. Opened the hood, charged the battery and tried to crank it. Would not budge. Starter would not engage. Disconnected the negative battery cable. Tried again. Still would not budge. After an hour of so of trying and using jumper cables from our other vehicle, still would not budge. I disconnected the negative battery cable from the right front fender ground and reattached it. It then cranked. Drove the vehicle 30 miles at interstate speed. 8 miles in city traffic. Drove home and parked it in the garage. Drove it abput 10-12 days later to get breakfast. Parked it, locked it with the key fob. Came back after getting food, key fob would not work. Opened it with the button on the door handle. Got In tried to crank it. Would not budge. Disconnected the negative battery cable twice, before it cranked, but would not drive. Message in dash said vehicle could not be driven. Finally got it cranked. GM never advised that the battery must have a 70% charge at all times for the electronics to work. Owner's manual contains no such statement. Vehicle is defective to the extent that it will leave me stranded in wherever the battery power is less than 70%. Dangerous to get stranded at night on a lonely road or highway, away from cities with tow trucks and competent service personnel. Vehicle in shop 32 days before dealer advised resolution. Modules bricked requiring engine control module and telematics module replacement.

BACK OVER PREVENTION — Filed 05/15/2025

The contact owns a 2025 GMC Yukon. The contact stated that while the vehicle was shifted into reverse, the rear-view camera displayed a black screen. The image in the rear-view camera was not visible, specifically in areas where there were reflective lights. The dealer was contacted and assisted the contact with the brightness options on the rear-view camera and stated there was no failure with the camera. The camera was not repaired or replaced. The manufacturer was made aware of the failure. The failure mileage was approximately 16.

UNKNOWN OR OTHER,VISIBILITY/WIPER — Filed 06/19/2026

On multiple occasions the center screen has been non operational when we start the car and just shows a black screen. The volume knob and screen power button are non-responsive. When this occurs the backup camera is inoperable, which is mandatory safety equipment. the HVAC also cannot be adjusted which could cause a windshield fogging condition which is a safety concern. The vehicle has been to the dealer 3 times for screen problems and the issue has not been resolved. When this occurs the problem persists for a few ignition cycles or for up to a couple of days and then will start functioning again. We have not been able to determine any specific condition that is causing the failure.

ENGINE — Filed 05/06/2026

Just over 6k miles, engine failure.

ENGINE — Filed 02/07/2026

The engine has seized and was replaced

ENGINE — Filed 03/19/2026

My engine completely failed on March 19, 2026 and it is currently at Sterling GMC in Bryan Texas waiting for a backorder engine as it needs to be completely replaced

UNKNOWN OR OTHER,BACK OVER PREVENTION — Filed 07/29/2025

My 2025 GMC Yukon's infotainment system has repeatedly failed. The huge center screen frequently goes black upon starting the car. Once the screen goes black you are unable to control literally dozens of the vehicle's features including but not limited to climate controls, safety features, heated/ventilated seats, gps, lane assist, the radio, no backup camera, etc. When the screen blacks out, the vehicle automatically turns the heat on to 76 degrees every single time and blows hot air from the front windshield defogger vents only. The list of features controlled by the touch screen is quite enormous. I have taken the vehicle to the GMC dealer four (4) times for software updates, none of which solved the problem and they have admitted they have no fix for this issue. The issue is widespread, as I have encountered literally hundreds of owners online like myself dealing with the very same problem; brand new cars that just do not work. GMC has done absolutely nothing to get to the bottom of this.

ENGINE — Filed 03/17/2026

Engine failure while driving at 60mph that started with a loud knocking sound to eventual engine failure where it wouldnt turn over. Vehicle has 9600 miles and has had issues since day one of leaving lot requiring fuel injector, intake manifold gasket, lifter and rod with last fix being new coil and spark plug that supposedly fixed issue. The most recent engine failure put my family and kids in danager given 100 degree weather in middle of desert on a small highway with very limited cell service. Vehicle provided no warning lights. Vehicle was towed to dealership and I have not received an update. Vehicle has not been inspected by polive or insurance or others.

AIR BAGS,ENGINE,FORWARD COLLISION AVOIDANCE — Filed 03/09/2026

Purchased new August 29, 2025 On 12/3/25- Mileage 4495. Took vehicle in for first maintenance service. Tire rotation and oil change. On 1/7/26- Reported grinding noise we had began noticing when starting vehicle. Engine light Service ESC. Service Traction control. Reported to Ben Mynatt GM. On 1/8/26 Mileage 7120- Took Yukon in for service due to grinding noise. Due for 6 module updates and 3 stand alone updates. On 2/16/26 Noticed ticking noise when heat in on high. Scheduled service for 2/26. On 2/24/26 Smell from car, oil reporting low. Dip stick completely dry. Sent email and photos to Ben Mynatt Service. On 2/26/26 Took vehicle in for service. Service advised to start oil consumption test. Ordered blower motor for the squealing noise. Cyl 3 misfire. Was told by the dealer, possibly needs engine 2/27/26 Took Vehicle in for service Check engine light on. Bearing inside blower motor and blower motor replaced. Replaced coil cyl 3 Tire Rotation 2/28/26 Car shaking, smoking, engine light on. Terrible smell from exhaust. Engine light came on, Service ESC, Service Traction Control, Forward Collision Unavailable, Reduced Acceleration Drive with Care Alert. GMC Alert: Service the engine and transmission system immediately alert, Engine Light on. Vehicle Approx miles. Codes misfires to cylinder 3. Took vehicle right to Service Dept. Codes Cleared. Replaced coil on cyl 3 March 7th - Mileage 11,200 Car shaking vigorously! Engine light flashing. Loud knocking coming from vehicle. GMC alert: Service the engine and transmission system immediately alert. Emission system- service now. Engine and Transmission System Service now. Service antilock braking, Stabilitrack stability control systems and airbag system. Service Air Bag System. Emailed to Service March 9th. Took vehicle in. Cylinder 3 & 8 misfire code cold start rough idle code. Oil consumption using approx1 qt of oil/500 miles. Vehicle unsafe risk of engine seizure, fire risk and loss of acceleration is extreme danger

ENGINE — Filed 02/11/2026

Vehicle went into limp mode while driving on the highway. Onstar said it was the transmission. Checked the oil and smoke was billowing out of the dip stick and there was no oil. None of the sensors indicated that there was low oil. After sitting and waiting for a tow truck rechecked the oil with the dipstick and there was oil in it. Now requires a new engine.

ENGINE — Filed 02/24/2026

The contact owns a 2025 GMC Yukon. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly went into LIMP Mode with a limited speed availability message displayed. The vehicle was restarted; however, the failure recurred. The vehicle was taken to the dealer, where it was diagnosed with engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 8,837

ENGINE — Filed 10/20/2025

The 3.0L diesel motor failed around 5700 miles. The thrust bearing failed and the engine and the turbo needed to be replaced.

ENGINE — Filed 02/04/2026

Engine started knocking and developed slow acceleration out of the blue. In addition car has locked up on freeway despite not having any cars around me. Its been in the shop for 3 days and still no diagnosis.

FORWARD COLLISION AVOIDANCE,LANE DEPARTURE — Filed 10/25/2025

While driving on a highway, the vehicle intermittently experienced a sudden loss of engine power during acceleration, accompanied by a flashing check engine warning light. The most serious event occurred while merging into traffic, when the vehicle failed to accelerate normally and briefly lost power, creating a risk of being struck by faster-moving vehicles. After pulling over and restarting the vehicle, normal acceleration temporarily returned, but the problem has recurred multiple times. The malfunction appears to be related to an engine misfire or powertrain fault because the check engine light flashes during the events and an OBD scan has shown misfire-related diagnostic codes (random/multiple misfire and a cylinder-specific misfire). The condition is intermittent and typically occurs after the vehicle has been driven for approximately 10–45 minutes. The vehicle remains available for inspection. The vehicle has been presented to authorized service departments multiple times for diagnosis. The dealerships have reported that they were unable to duplicate the issue during road testing and no lasting repair has been completed. The manufacturer has been contacted and the vehicle has been inspected/diagnosed through authorized service channels, but the underlying cause has not been identified. The failure continues to occur intermittently and is a safety hazard because it affects acceleration in traffic. Incident list 10/25/2025 (~12:25 PM; ~3,108 miles) — While accelerating to merge onto a highway, the vehicle lost power and the check engine light flashed. The driver pulled over, shut the vehicle off, restarted, and the condition temporarily resolved, allowing the trip to continue. 10/27/2025–11/04/2025 — The same loss-of-power/misfire behavior recurred intermittently, typically lasting a few minutes before clearing. 11/05/2025 (~8:01 AM; ~3,641 miles) — The check engine light flashed again and symptoms consistent with misfire/loss of power were present. The

POWER TRAIN,ENGINE — Filed 10/25/2025

While driving on a highway, the vehicle intermittently suffers a sudden loss of engine power during acceleration, accompanied by a flashing check engine light. The most serious event occurred while merging into traffic when the vehicle failed to accelerate normally and briefly lost power, creating a risk of being struck by faster-moving vehicles. Pulling over and restarting temporarily restores normal acceleration, but the problem recurs. The malfunction appears consistent with an engine misfire/powertrain fault. An OBD scan has shown misfire-related diagnostic codes (random/multiple misfire and a cylinder-specific misfire). The condition is intermittent and often occurs after approximately 10–45 minutes of driving. The vehicle remains available for inspection. The vehicle has been presented to authorized service departments multiple times. Dealers reported they were unable to duplicate the issue during road testing and no lasting repair has been completed. The manufacturer has been contacted and the vehicle has been evaluated through authorized service channels, but the underlying cause has not been identified. This remains a safety hazard because it reduces acceleration in traffic. Incident list: • 10/25/2025 (~12:25 PM; ~3,108 miles): Loss of power while merging; flashing CEL; restart temporarily resolved. • 10/27/2025–11/04/2025: Intermittent recurrence, usually lasting a few minutes then clearing. • 11/05/2025 (~8:01 AM; ~3,641 miles): Flashing CEL and misfire/loss-of-power symptoms; taken for service. • 11/26/2025 (~10:06 AM): Another episode consistent with the same pattern. • 12/17/2025 (~8:21 AM): Another episode, including during travel to a service visit. • Ongoing: Episodes after ~10–45 minutes; sometimes requires restart to restore drivability. Observed codes: P0300 and P0301. Safety risk: loss of power during acceleration/merging increases risk of rear-end or side-impact collision.

POWER TRAIN,ENGINE — Filed 01/29/2026

ENGINE died rattling sound undeer car shaking loss of power

ENGINE — Filed 09/27/2025

suddenly went into limp mode on the highway, engine had to be replaced due to bearing failure sending metal through the engine

ELECTRICAL SYSTEM,UNKNOWN OR OTHER — Filed 03/15/2025

The wireless charging pad in the vehicle below the climate control system. Yes, it is. The charging component malfunctioned and overheated the back of my phone when it was set in the console while driving. I had no intention of charging my phone, but instead place my phone down while driving. When I picked up my phone at a stop light, I laid it in my inner thigh when the light changed. The burning was so intense and unexpected I swerved into oncoming traffic and lost control, momentarily of the vehicle. I have recreated the incident in a controlled environment myself and the issue is still active. I am happy to have the issue confirmed independently. I gave notice to the dealership after it happened with no concern or further investigation. No, the vehicle has not. No, no warning at all. In fact this is my 3rd GMC Yukon since 2016 and all 3 have had the wireless charging pad, I have had the same phone as my last one. I never had an issue or experienced anything like this.