Honda Accord Investigations
NHTSA Office of Defects Investigation records
Electrical overstress
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW.  The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications.  The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU.  In
Loss of Direction Control
On May 6, 2021, the Office of Defects Investigation (ODI) opened Engineering Analysis (EA21-001) to assess a sudden loss of steering control, in Model Year (MY) 2013-2015 Honda Accord vehicles. Consumers alleged while driving the steering wheel would pull to the left or the right independently. Steering pull may pose a risk of loss of directional control. Honda stated that they believed the inadvertent steering input was caused by a loose magnet located within the electronic power steering (EPS) system. Due to poor formulation of the adhesive, this magnet can become loose and move up to 2 degrees around the steering column. When the magnet moves, the torque sensor generates a signal that results in unwanted steering in either direction. Honda stated the steering force required to maintain directional control with a loose magnet is a maximum of 3-pound feet. The maximum force of the unwanted steering input can be overcome by the driver and is similar to driving on grooved pavement.The Vehicle Research Test Center (VRTC) sent over 4,000 questionnaires to 2013-2015 Honda Accord vehicle owners. Of the 637 responses, 58 consumers experienced unwanted steering. Consumers experiencing unw
Inadvertent Automatic Emergency Braking
On February 21, 2022, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE22003) to assess reports of inadvertent activation of the Collision Mitigation Braking System (CMBS), an automatic emergency braking (AEB) system, in model year 2017-2019 Honda CR-V and 2018-2019 Honda Accord vehicles. The reports allege that activation of the AEB system occurs while driving with no apparent obstruction in the vehicle's forward path, resulting in sudden vehicle deceleration. Honda indicated that they were aware of a total of X,XXX reports that may relate to the alleged defect. Honda provided analysis of the alleged defect and alleges that some customers possibly had an inadequate understanding of the CMBS and its limitations.  However, many consumer complaints allege that Honda dealerships were unable to reproduce the condition or state that they were informed that this is considered normal CMBS operation. To date, ODI has received a total of 1,294 consumer complaints of inadvertent activation of CMBS in 2017-2022 Honda CR-V and 2018-2022 Honda Accord vehicles. A total of 31 complaints alleged a crash and 50 alleged an injury. The Total column in the Failure Report
Inadvertent Automatic Emergency Braking
On February 21, 2022, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE22003) to assess reports of inadvertent activation of the Collision Mitigation Braking System (CMBS), an automatic emergency braking (AEB) system, in model year 2017-2019 Honda CR-V and 2018-2019 Honda Accord vehicles. The reports allege that activation of the AEB system occurs while driving with no apparent obstruction in the vehicle's forward path, resulting in sudden vehicle deceleration. Honda indicated that they were aware of a total of X,XXX reports that may relate to the alleged defect. Honda provided analysis of the alleged defect and alleges that some customers possibly had an inadequate understanding of the CMBS and its limitations.  However, many consumer complaints allege that Honda dealerships were unable to reproduce the condition or state that they were informed that this is considered normal CMBS operation. To date, ODI has received a total of 1,081 consumer complaints of inadvertent activation of CMBS in the subject vehicles. A total of 24 complaints alleged a crash and 42 alleged an injury. The Total column in the Failure Report Summary removes duplicate reports
Front Seat Belt Assemblies may be Missing the Rivet that Secures the Quick Connector and Wire Plate
On April 4, 2024, the Office of Defects Investigations (ODI) opened RQ24006 to investigate American Honda Motor Co.âs (Hondaâs) proposed remedy for recall 23V-782 as well as scope of the vehicles involved. Honda issued recall 23V-782 on November 21, 2023, which concerns certain model year (MY) 2023-2024 Honda Accord, Honda Accord Hybrid, and Honda HR-V vehicles. Recall 23V-782 states that the driver and front passenger seat belt pretensioner assemblies may have been manufactured without a rivet that secures the pretensioner quick connector and wire plate. Recall documentation states that seat belt pretensioner assemblies that are missing the rivet will not properly restrain the occupant in the event of a collision, increasing the risk of injury.Subject defective seat belt assemblies are installed as original equipment for both the driver and front passenger positions for the HR-V, but only for the driver position for the Accord and Accord Hybrid. The recall remedy for 23V-782 instructs the technician to inspect both front seat belt pretensioner assemblies and, if necessary, replace them. The inspection procedure requires the technician to utilize a pull force gauge to determine
About NHTSA Investigations
NHTSA investigations include Preliminary Evaluations (PE), Engineering Analyses (EA), Defect Petitions (DP), and Audit Queries (AQ). Investigations may lead to recalls if defects are confirmed. An open investigation means NHTSA is actively examining the issue.